Well, I have the oil paint, oderless mineral spirits and an acrylic painted M60A1 in desert sand. I now need advice on how to do pin washes.
Thanks, Greg.
AFV Painting & Weathering
Answers to questions about the right paint scheme or tips for the right effect.
Answers to questions about the right paint scheme or tips for the right effect.
Hosted by Darren Baker, Matthew Toms
Pin washes?
TopSmith
Washington, United States
Joined: August 09, 2002
KitMaker: 1,742 posts
Armorama: 1,658 posts
Joined: August 09, 2002
KitMaker: 1,742 posts
Armorama: 1,658 posts
Posted: Wednesday, August 16, 2006 - 05:04 AM UTC
Tojo72
North Carolina, United States
Joined: June 06, 2006
KitMaker: 4,691 posts
Armorama: 3,509 posts
Joined: June 06, 2006
KitMaker: 4,691 posts
Armorama: 3,509 posts
Posted: Wednesday, August 16, 2006 - 06:22 AM UTC
I just did my Jagdpanther yesterday!!!just make sure you have it sealed with gloss clear acrylic,than just touch the brush to the seams,doors hatches nuts +bolts,and just like the other posts say-it really runs nicely down the seams.If too much goes on just swab it off with a q-tip.Experiment a little till you like what you see.Allow to dry and seal with flat acrylic..........I was really happy with my results.
good luck
good luck
M4Nut
California, United States
Joined: March 22, 2002
KitMaker: 148 posts
Armorama: 80 posts
Joined: March 22, 2002
KitMaker: 148 posts
Armorama: 80 posts
Posted: Wednesday, August 16, 2006 - 06:48 AM UTC
One thing Anthony didn't mention is to use a small brush. You want to be able to just put enough of a wash on to shadow the item; ie. a bolt, tie down, so forth.
Good luck,
Eric
Good luck,
Eric
Genetk44
Quebec, Canada
Joined: March 17, 2006
KitMaker: 85 posts
Armorama: 73 posts
Joined: March 17, 2006
KitMaker: 85 posts
Armorama: 73 posts
Posted: Wednesday, August 16, 2006 - 09:02 AM UTC
Why do you have to seal it with gloss first before doing the pin wash?
Cheers
Gene
Cheers
Gene
mightymouse
British Columbia, Canada
Joined: June 25, 2006
KitMaker: 104 posts
Armorama: 0 posts
Joined: June 25, 2006
KitMaker: 104 posts
Armorama: 0 posts
Posted: Wednesday, August 16, 2006 - 09:08 AM UTC
Quoted Text
Why do you have to seal it with gloss first before doing the pin wash?
Cheers
Gene
It helps protect the finished paint job by sealing it in so that there is a lesser chance of a reaction with the finished paint job and the wash. It also, most importantly, helps the wash flow smoothly along the surface of the model.
Darson
Victoria, Australia
Joined: June 14, 2005
KitMaker: 247 posts
Armorama: 129 posts
Joined: June 14, 2005
KitMaker: 247 posts
Armorama: 129 posts
Posted: Wednesday, August 16, 2006 - 11:15 AM UTC
Quoted Text
Why do you have to seal it with gloss first before doing the pin wash?
Cheers
Gene
Just to add a little to what Mike said, if you don't gloss coat your model prior to a pin wash the paint you are using for a wash will bleed into your paint work rather than flowing smoothly along the surface. Also it becomes very difficult to remove any excess afterwards.
Posted: Wednesday, August 16, 2006 - 12:32 PM UTC
one of the best things to gloss coat your model with is Johnsons Future - just spray it unthinned and clean airbrush with rubbing alcohol after.
HTH
Andy
HTH
Andy
Achilles958
England - South East, United Kingdom
Joined: August 01, 2006
KitMaker: 16 posts
Armorama: 0 posts
Joined: August 01, 2006
KitMaker: 16 posts
Armorama: 0 posts
Posted: Thursday, August 17, 2006 - 09:41 PM UTC
Just used Future/Klear for the first time over Tamiya acrylics which had dried for about 24 hours and it seemed to start taking the paint off before it dried. Is this normal?
Javlin813
Illinois, United States
Joined: September 14, 2005
KitMaker: 336 posts
Armorama: 191 posts
Joined: September 14, 2005
KitMaker: 336 posts
Armorama: 191 posts
Posted: Friday, August 18, 2006 - 04:37 AM UTC
Hi Tim,
While I don't generally use acrylics, what you described does not sound right. You might need to let the paint cure a little longer but for acrylics 24 hours should have been sufficient.
Here is a link that explains about using Future/Klear http://www.swannysmodels.com/TheCompleteFuture.html
Hope this helps,
Scott
While I don't generally use acrylics, what you described does not sound right. You might need to let the paint cure a little longer but for acrylics 24 hours should have been sufficient.
Here is a link that explains about using Future/Klear http://www.swannysmodels.com/TheCompleteFuture.html
Hope this helps,
Scott
Genetk44
Quebec, Canada
Joined: March 17, 2006
KitMaker: 85 posts
Armorama: 73 posts
Joined: March 17, 2006
KitMaker: 85 posts
Armorama: 73 posts
Posted: Friday, August 18, 2006 - 10:55 AM UTC
Thanks for the answers guys.
Cheers
Gene
Cheers
Gene
TopSmith
Washington, United States
Joined: August 09, 2002
KitMaker: 1,742 posts
Armorama: 1,658 posts
Joined: August 09, 2002
KitMaker: 1,742 posts
Armorama: 1,658 posts
Posted: Friday, August 18, 2006 - 12:18 PM UTC
Thanks Guys! Tomorrow the Tank goes for a wash. Greg