In-Box Review
Sd.Kfz.251 Ausf. D PE Update (for DML 6233)

by: Pawel Krupowicz [ VODNIK ]


The set is designed for Dragon's "three in one" Sd.Kfz.251 Ausf.D kit and it includes parts to improve details in the basic 251/1 variant (there is also additional set #35043 from Voyager with parts specific to 251/9 7.5cm KwK37 (L/24) version). This set, while described as "PE Update" in instructions, is much more than that as aside from photo-etched parts, it also includes resin and plastic pieces.

The set is packed in a new style packaging. "CD case" type paper card envelopes previously used by Voyager were replaced by similar in size, but much thicker card boxes. The familiar black and orange design of boxes however was retained. New packaging gives more space inside to include resin parts. Inside the box of set 35045 we find instructions printed on both sides of A4 size paper sheet and two re-sealable plastic bags. The bigger bag with all the PE parts on 8 frets inside is attached to the rectangle of stiff paper for protection. In this bag are also ABS plastic rods and printed acetate part. On the back side of the box is a drawing showing the contents of the set, but it is misleading, as a few of shown PE frets are different from these included in the set. The content of the set is correct for this product, so the picture is wrong (it shows some frets from the #35043 set) and cannot be used to check the completeness of the package.

Sizes of photo-etched frets are:
A - 64 mm x 95 mm / 0.15 mm thick brass
B - 64 mm x 95 mm / 0.15 mm thick brass
C - 64 mm x 95 mm / 0.15 mm thick brass
D - 64 mm x 95 mm / 0.15 mm thick brass
E - 24 mm x 32 mm / 0.15 mm thick brass
F - 24 mm x 39 mm / 0.25 mm thick brass
P1 - 18 mm x 32 mm / 0.05 mm thick aluminum (or steel?)
WW2 German Clamps & Clasps - 32 mm x 32 mm / 0.15 mm thick copper.

Resin parts included are:
- two complete front wheels with nice rim details on both sides and well defined tire tread pattern,
- MG42 machine gun,
- ax,
- pickax,
- tiny switch console for dashboard.

Additional parts are two approx. 100 mm long ABS rods - one 0.45 and the other 0.6 mm diameter (although instructions call for use of 0.5 and 1mm diameter rods!) - and a piece of clear acetate with dashboard instrument faces printed on it.

Some of included PE parts are:

- stencils (P1) for painting vehicle type and weight data for 251/1D, 251/9D and 251/20 vehicles, to use instead of decals included in Dragon kit.
- dashboard (with extra resin detail and clear acetate instrument faces).
- fire extinguisher holder.
- clamps for tools and weapons (with resin ax and pickax also included). Thanks to the inclusion of complete PE fret from the WWII German Clamps & Clasps set we get more tool clamps than is needed for this one model.
- padlocks with chains for storage boxes.
- side bins and a few complete storage boxes.
- radio rack.
- roof section above the driver's compartment.
- mud flaps.
- replacement floor plates with fine non-skid pattern (requires removal of molded-on details from kit part).
- rails for the vehicle interior sides - with PE brackets and ABS rod bars.
- many other small details parts which I unfortunately cannot identify (see instructions scans).

The quality of etched parts is very high and they include really tiny details, so some care is needed when removing them from frets. The assembly of some small parts, like tool clamps, may be tricky and it requires a stable hand, good tools and some patience, but once assembled, those details should look great. Modelers with no experience with PE parts probably should not start their adventure with this kind of aftermarket products from this set. Resin parts are nice addition and the quality of casting is very good with no air bubbles and crisp details. To my (overly geometry sensitive) eye the resin wheels are a tiny little bit deformed and the shape is not perfectly regular (and I don't mean weight flattening, which is well done), but it is a common problem of resin wheels and in this case the deformation is really minimal.

Instructions are very clear, but do not mention resin wheels or MG42. Luckily these parts simply replace kit parts. Also not mentioned are painting stencils, but it should not be too difficult to figure out how to use them.

Another nice set from Voyager and addition of ABS rods, resin parts and inclusion of photo-etched frets of different thickness significantly increase its value in comparison to usual PE-only sets.

Many thanks to Voyager Model for the review sample!
The multimedia set is designed for Dragon's 'three in one' Sd.Kfz.251 Ausf.D kit and it includes parts to improve details in the basic 251/1 variant.
  Scale: 1:35
  Mfg. ID: PE35045
  Related Link: Voyager Models
  PUBLISHED: Jun 08, 2005

About Pawel Krupowicz (Vodnik)

As first lines of this bio appear under all my reviews, I feel it is important that I start with this information: In March 2005 I ventured into the other side of modeling "industry" - I was not only building model kits, but also helping design them as a consultant for Dragon Models Ltd.. These days...

Copyright 2021 text by Pawel Krupowicz [ VODNIK ]. All rights reserved.


Click image to enlarge
  • PE35045_00
  • PE35045_01
    Contents of the set.
  • PE35045_03
    First page of instructions.
  • PE35045_04
    Second page of instructions.
  • PE35045_09
    Photo-etched fret A.
  • PE35045_08
    Photo-etched fret B.
  • PE35045_07
    Photo-etched fret C.
  • PE35045_06
    Photo-etched fret D.
  • PE35045_05
    Small PE frets, clear acetate sheet and ABS rods.
  • PE35045_02
    Resin Parts